I tried this , however unfortunately did not help in my case. I am still trying to figure out through some hit and trial and am sure this would be something silly as I have almost followed everything per the documentation.

Will post back if I find something.. Hopefully I will :)

On Tue, Mar 17, 2015 at 5:26 AM, Brendan Kearney bpk678@gmail.com wrote:

On Mon, 2015-03-16 at 13:24 -0400, brendan kearney wrote:

...

Thank you for validating my complaint.

The trick to this is "string matching", not putting the same name in both places. I have played around with several different configs and finally got it working. I think the trailing slashes were what got things working for me. I am not in front of my setup right now, but will reply later today when I am.

On Mar 16, 2015 12:39 PM, "Divya Vikraman" divya.divyavikram@gmail.com wrote: Hi,

    I am using openldap 2.4.39 version and trying to set up multi
    master replication.


    This is my configuration

    ServerID        1 "ldap://ldap1-test.com"
    ServerID        2 "ldap://ldap2-test.com"

    overlay         syncprov
    syncprov-checkpoint     10 1
    syncprov-sessionlog     100

    syncrepl        rid=1
                    provider="ldap://ldap1-test.com"

    binddn="uid=replication,ou=People,dc=ldap,dc=nqa,dc=test,dc=com"
                    bindmethod=simple
                    credentials="xyzabc"
                    searchbase="dc=ldap,dc=nqa,dc=test,dc=com"
                    type=refreshAndPersist
                    interval=00:00:00:10
                    retry="5 10 60 +"
                    timeout=1
                    schemachecking=off
                    scope=sub

    syncrepl        rid=2
              provider="ldap://ldap2-test.com"

    binddn="uid=replication,ou=People,dc=ldap,dc=nqa,dc=test,dc=com"
                    bindmethod=simple
                    credentials="xyzabc"
                    searchbase="dc=ldap,dc=nqa,dc=test,dc=com"
                    type=refreshAndPersist
                    interval=00:00:00:10
                    retry="5 10 60 +"
                    timeout=1
                    schemachecking=off
                    scope=sub

    MirrorMode      on



    I have put the below entries in /etc/default/slap


    on server 1
    SLAPD_SERVICES="ldapi:// ldap://ldap1-test.com"


    and server 2
    SLAPD_SERVICES="ldapi:// ldap://ldap2-test.com"



    After this I am not able to start the service and when I do a
    slapd -d sync , I get the error "read_config: no serverID /
    URL match found"



    I have seen a similar issue posted in an earlier thread but
    could not find a solution.



    Thanks,


    Divya

an ldapsearch shows these lines (note, no quotes around the ldap URL):

olcServerID: 1 ldap://192.168.88.1 olcServerID: 2 ldap://192.168.88.2

i am running fedora 20, and /etc/sysconfig/slapd has the line:

SLAPD_URLS="ldapi:/// ldap://192.168.88.1"

the undocumented nature of this causes a lot of consternation, but strangely there is no one else offering insight to this. Thus, we are left to our wild @$$ guessing.

i believe the quotes in your config are why the string matching is failing. try removing the quotes, so that your lines are:

ServerID 1 ldap://ldap1-test.com ServerID 2 ldap://ldap2-test.com

if that does not work, you will need to iterate through trial and error until you find a working config. because i have a dependency on LDAP for bind/named to work, i use IPs in my configs. if your DNS is done elsewhere and you dont have the dependency i have, you should be able to get things working.