Hello Eric,
I had used openldap 2.3.26. I had
added the index after starting the slapd , the first approach as you said ,
using ldapmodify in cn=config.
After I add it , when I restart the slapd
server, the indexes , I added before is not there. It is due to , I started the
server like ./slapd -d -1 -f ./slapd.conf right? But When I try starting the server
using ./slapd -F /etc/openldap/slapd.d/ -f /etc/openldap/slapd.conf",
then also I am getting some problems after restarts.
Is this way of starting the server is
correct for dynamic indexing case?
Thanks a lot in advance,
Arunachalam.
********************************************************************************************************
This e-mail and attachments
contain confidential information from HUAWEI, which is intended only for the
person or entity whose address is listed above. Any use of the information
contained herein in any way (including, but not limited to, total or partial
disclosure, reproduction, or dissemination) by persons other than the intended
recipient's) is prohibited. If you receive this e-mail in error, please notify
the sender by phone or email immediately and delete it!
-----Original Message-----
From: openldap-software-bounces+arunachalamp=huawei.com@OpenLDAP.org
[mailto:openldap-software-bounces+arunachalamp=huawei.com@OpenLDAP.org] On
Behalf Of Eric Irrgang
Sent: Wednesday, June 27, 2007 2:35 AM
To: Arunachalam Parthasarathy
Cc:
Subject: Re: Dynamic Indexing through cn=config
What version of OL are you running?
It sounds like the new index was not
built properly. How did you add the
indexing? You should either
a) add the index while slapd is
running by doing an ldapmodify to the
database entry in cn=config
or
b) stop the slapd server, edit the
config, run slapindex, and then restart
the server
Any other approach will yield strange
results.
On Thu, 21 Jun 2007, Arunachalam
Parthasarathy wrote:
> Hello,
>
>
>
> I used bdb as a backend
>
> Started slapd with ,
./slapd -h "ldap://<ip>:<port>" -F
> /etc/openldap/slapd.d/ -f
/etc/openldap/slapd.conf"
>
> Step 1: I added indexing on a
attribute (sn), in the cn=config sub-tree,
>
> Step 2: If I search through the
tree (cn=config), the added entry is not
> reflected
>
> To Check, I added entries, it
was not indexed on the added attribute (sn.bdb
> is not getting generated in bdb
directory)
>
> Step 3: When I try to add one
more time , the same entry as Step 1, it says
> , entry already exists
>
> Step 4: Now when I search
cn=config tree, I am able to see the sn index
> entry in olCDbIndex
>
> Now I added entries, it was
getting indexed on the added attribute (sn.bdb
> is generated in bdb directory)
>
>
>
> Please say why is this happening
>
>
>
> Thanks a lot in advance,
>
> Arunachalam.
>
>
>
>
>
>
>
>
>
>
****************************************************************************
> ****************************
> This e-mail and attachments
contain confidential information from HUAWEI,
> which is intended only for the
person or entity whose address is listed
> above. Any use of the
information contained herein in any way (including,
> but not limited to, total or
partial disclosure, reproduction, or
> dissemination) by persons other
than the intended recipient's) is
> prohibited. If you receive this
e-mail in error, please notify the sender by
> phone or email immediately and
delete it!
>
>
>
>
--
Eric Irrgang - UT